Commercial Electric CER5742WH Manuel d'instructions télécharger pdf

GENERAL: All electrical connections must be in accordance with local and

National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper

electrical wiring connections obtain the services of a qualified electrician.

Remove the trim from the box and make sure that no parts are missing by

referencing the PARTS illustrations.

THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LED

LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE

DETERMINED BY CSA OR CANADIAN AUTHORITIES HAVING

JURISDICTION.

WARNING – RISK OF ELECTRIC SHOCK. INSTALL THIS TRIM IN

RECESSED HOUSINGS THAT HAVE DIMENSIONS SHOWN IN FIG. 1,

WHICH INCLUDE THE FOLLOWING LUMINAIRES: INCANDESCENT

HOUSINGS – COMMERCIAL ELECTRIC HBR5ICAT, HBR5ICRAT, HBR5,

HBR5R; HALO H5T, H5RT, H5ICT, H5RICAT, H5RICAT; CORDELIA

MODELS X5LICAT, X5LICRAT; ELCO MODELS EL5ICA, EL5RICA;

LITHONIA MODELS L5, L5R; ELITE MODELS B5, B5R, B5IC, B5RIC.

____________________________

ASSEMBLY AND INSTALLATION

INCANDESCENT HOUSINGS

1.Unscrew the WING NUT inside the CAN to detach the SOCKET BRACKET

from the CAN. Disengage the SOCKET from the SOCKET BRACKET. (FIG.

2.Thread the SOCKET ADAPTER into the SOCKET. (FIG. 3)

3.Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the MALE

CONNECTOR of the SOCKET ADAPTER ASSEMBLY. (FIG. 4)

4.Squeeze both TORSION SPRING arms together and insert into the

TORSION SPRING SLOTS (or RECEIVER BRACKETS) of the CAN. Tuck

all wires into the CAN and carefully push the RETROFIT TRIM into CAN.

(NOTE: To provide enough room in shallow cans, carefully position SOCKET

ADAPTER and SOCKET adjacent to the long side of the LED DRIVER prior

to inserting the RETROFIT TRIM into the CAN.) (FIG. 5)

LED HOUSINGS

1.Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the MALE

CONNECTOR of the HALO HOUSING. (FIG. 4)

2.Squeeze both TORSION SPRING arms together and insert into the

TORSION SPRING SLOTS (or RECEIVER BRACKETS) of the CAN. Tuck

all wires into the CAN and carefully push the RETROFIT TRIM into CAN.

(FIG. 5)

________

DIMMING

Although this product is compatible with most common residential type

dimmers, dimming performance depends on dimmer, dimmer setting (for

dimmers with brightness range adjustments), wiring method, and the number

of LED modules. For best results, set dimmer position at maximum before

adjusting to a lower light level.

Recommended Dimmers (minimum load for four LED modules maybe

required for optimal dimming performance): Leviton Decora – 6631, IPI06,

Lutron Skylark – S-603PGH, and Lutron Diva – DVWCL-153PDH, CTCL-

15PDH, and TGCL-153PH.

WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN

POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING

OR SERVICING THE FIXTURE.

LED 5” RETROFIT TRIM INSTALLATION

INSTRUCTIONS - MODEL CER5742

Please read carefully and save these instructions, as

you may need them at a later date.

QUESTIONS? CALL TOLL

FREE 1-800-345-0542

5 in. – 7 in.

5 in.

FIG. 1

FIG. 2

FIG. 3

PARTS

SOCKET ADAPTER

ASSEMBLY

RETROFIT TRIM

HOUSING DIMENSIONS

FIG. 4 FIG. 5

1 2 3 4 5 6

Résumé du contenu

Page 1 - INSTRUCTIONS - MODEL CER5742

GENERAL: All electrical connections must be in accordance with local andNational Electrical Code (N.E.C.) standards. If you are unfamiliar with proper

Page 2 - MODEL: RHPS311CL-JW1

Page 3 - 1-800-345-0542

GENERAL: Todas las conexiones eléctricas deben realizarse conforme alas normas locales y al Código Eléctrico Nacional (N.E.C. por sus siglasen inglés)

Page 4 - MODELO: RHPS311CL-JW0

Page 5 - MODÈLES CER5742

AVERTISSEMENT – RISQUE DE DÉCHARGE ÉLECTRIQUE. COUPEZ LE COURANT AU NIVEAU DU DISJONCTEUR OU DE LA BOÎTE DE FUSIBLES AVANT D’INSTALLER OU D’EFFECTUE

Page 6 - MODÈLE: RHPS311CL-JW0