Commercial Electric CER5741AWH30 Manuel d'instructions télécharger pdf (Page 2)

_______________________________

FIVE-YEAR LIMITED WARRANTY

Commercial Electric



warrants this product to be free from

defects in material and workmanship for five years from the original

date of purchase by the consumer. This warranty is limited to the

counter replacement at the time of purchase, with the original

purchase receipt. Commercial Ele ctric



will not be liable for the

loss or damage of any kind, incidental or consequential damages

of any kind, whether based on warranty contract or negligence,

and arising in connection with the sale, use or repair of the product

claimed to be defective. Some states do not allow the exclusion or

limitation of incidental or consequential damages so the above

limitation may not apply to you. This warranty gives you specific

legal rights and you may also have other rights, which vary from

state to state. Misuse, accident, improper installation or

maintenance will also void the warranty.

_____________________________

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiver antenna.

• Increase the separation between the equipment and receiver.

• Install the product onto on a circuit different from that to

which the receiver is connected.

• Consult with the dealer or an experienced radio/TV

technician for help.

CAUTION: Any changes made to the electronics circuit will void

this equipment’s compliance with Part 15 of the FCC Rules and

should not be operated.

________

DIMMING

Dimming performance may depend on the dimmer, the dimmer

range adjustment setting (for dimmers with brightness range

adjustments), the wiring method, and/or the number of LED

modules installed onto the dimmer circuit.

• For dimmer selection, it is recommended to use one of the

following dimmers:

Leviton Decora SureSlide® – 6631, 6674 (Universal); Leviton

IllumaTech® - IPI06-1L, IPL06-10 (Universal)

Lutron Ariandni®/Toggler® - TGCL-153P, AYCL-153P; Lutron

Diva® - DVWCL-153P, DVCL-153P; Lutron Luméa® - LGCL-

153P, Lutron Maestro® - MACL-153M; Lutron Skylark® - S-

600, S-603P, SCL-153P; Lutron Skylark Contour™ - CTCL-

153P.

• For best results, it is recommended to install a minimum of four

LED modules onto one dimmer.

• Before turning on the LED lights, set dimmer position at

maximum before adjusting to a lower light level.

• Please follow the dimming control manufacturer’s instructions

for the installation of all dimming controls.

_____________________

DRIVER REPLACEMENT

1. DISCONNECT MAIN POWER AT FUSE OR CIRCUIT

BREAKER.

2. Pull the RETROFIT TRIM down from the RECESSED

HOUSING. Unplug the FEMALE CONNECTOR of the

RETROFIT TRIM from the MALE CONNECTOR of the

SOCKET ADAPTER ASSEMBLY.

3. Pull the TRIM RING from magnets built into the CAST HEAT

SINK. (FIG. 6)

4. Press the four lens tabs in as shown to carefully remove the

plastic LENS. (FIG. 8)

5. Remove the DRIVER SCREWS and separate the old LED

DRIVER from the CAST HEAT SINK. (FIG. 8)

6. Detach the LED DRIVER WIRES from the LED TERMINAL

BLOCK by depressing down on the provided TERMINAL

TABS. (FIG. 10)

7. Mount the new LED DRIVER onto the CAST HEAT SINK

using the previously removed DRIVER SCREWS. (FIG. 8)

8. From the new LED DRIVER insert the RED (or BLACK) WIRE

into the HOT TERMINAL (marked with a “+” on the LED

BOARD) and the YELLOW (or WHITE) WIRE into the

NEUTRAL TERMINAL (marked with a “-” on the LED BOARD)

of the TERMINAL BLOCK. (FIG. 11)

9. Replace the LENS. Replace the TRIM RING. (FIG. 6)

10. Re-install the RETROFIT TRIM into the RECESSED

HOUSING. (FIG. 5)

Class 2 Power Supply | Dry or Damp Location Only

CAUTION

DISCONNECT LINE VOLTAGE BEFORE INSTALLING OR

REPLACING

VEL12045120HDA-3

In: 15W, 0.15A

Out: 22-28V, 450mA

PF: >0.90

CONSTANT CURRENT

Dimmable LED Driver

120V 60Hz

RoHS

E339538

Santa Fe Springs, CA

www.espentech.com

V2 Toll Free 1-866-933-7736 Made in China

W Red

B Yel

N +

L -

FIG. 10 FIG. 11

FIG. 9

FIG. 8

REV 04-AUG-14

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Commercial Electric CER5741AWH30 Manuel d'instructions Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Non Commercial Electric CER5741AWH30